TURBO TURF HS-150-P HYDROSEEDER
Seed 2,000 sq. ft. per load
Mix in minutes, spray a load in 10 minutes
Simple operation, learn to run in minutes
Full pressure control for great trimming.
Reliable Honda engine
Clean up in minutes at the end of the day.
Few moving parts and low maintenance.
Add a boom and use as a lawn sprayer
The HS-150-P, is a 150 Gallon, pull type hydroseeder. It has a clevis hitch (pin hitch) and two 205/65-10 tires on demountable hubs and is designed for off road use. It will seed 2000 square feet per load. It is equipped with a 6.5H.P. Honda engine that is directly coupled to a 2″ X 2″ high volume centrifugal pump. The unit comes with 100′ of 1 1/4″ discharge hose, A gun and three nozzles (1 wide hydroseeding nozzle, 1 straight distance nozzle, and 1 trim nozzle). The empty weight of the unit is 380 pounds. the loaded weight is 1580 pounds. the physical dimensions are 41″W x 84″L x 52″H. This unit is easily pulled by a compact tractor, ATV or a utility vehicle such as the John Deere Gator.
The HS-150-P hydroseeder is ideal for a golf course for repairing wear along cart paths, and for repair projects, for a cemetery, for a school, for construction repairs such as someone installing irrigation systems or water lines, for installing a new lawn in areas with smaller lawns and for lawn repair and renovation . It is capable of handling much larger jobs. Material is applied at approximately 30 G.P.M. Time to spray a complete tank is about 4-5 minutes. Mixing time is 2-5 minutes depending on material. This unit comes with 100′ of discharge hose. It will handle an extra 50′ of hose. The spray distance with the straight nozzle is approximately 40′.
Typically materials used in one load would be 1 1/2 bags of pourable mulch such as Cover Grow or EZ-Mulch AF or 40-50 pounds of paper mulch, the appropriate amount of seed for 2000 sq. ft. (any seed will work in hydroseeding), and the appropriate fertilizer for 2000 square feet (liquid, water soluble, or granular).
Like all TURBO TURF systems the HS-150-P comes equipped with a long life poly tank that can never rust, the ability to mix partial loads, a simple but powerful design with few moving parts, continuous agitation, and the ability to control the flow at the gun without making adjustments at the unit. Prices quoted are for a complete machine ready to operate. The HS-150-P hydroseeder is a pull type units that is intended for off road use and is not intended to be pulled on roads or highways.
This unit used a 2″ x 2″ centrifugal pump with an output of –190 gallons a minute of flow and 42 P.S.I. of pressure. We have been using this pump for nearly 20 years and it has provided excellent performance and durability. The housing material is cast aluminum and it is easy to service and maintain. There are no grease fittings and the only maintenance required is to winterize if at the end of the season if it is stored where temperatures go below freezing. The pump impeller mounds on the end of the engine shaft so there is no power loss. Typically it can operate for 5 to 10 years with no maintenance. The only thing to be careful of is to not run it dry.
This unit comes with a 6.5 H.P. Honda recoil start engine. This has proved to be a very reliable engine with a long life. The engine has a two year warranty and service for the engine is available at any authorized Honda engine dealer.
This unit comes standard with 100 ft of 1 1/4″ I. D. hose. The hose we use is both strong and light weight. It is made from a poly material with a spiral reinforcement. Additional hose is available in 50 foot sections. The unit will handle up to 150 feet of hose.
This unit is easy to run. There are only two valves on the unit. The main mixing valve is opened fully when mixing and closed to a 45 degree angle in which case it is half open and half closed. This provides some mixing action but gives added spray power. There is also a valve going to the discharge hose. This is always fully open when spraying but can be closed to disconnect the discharge hose. The discharge hose is connected with a quick coupler. Should you need to go someplace to get water the hose can quickly be disconnected so when you have a new load mixed up you can connect the hose and start spraying right where you left off. It eliminates the need to wrap up the hose before you are finished.
The HS-150 is a skid type unit that can be operated from a small trailer, from the back of a pickup truck from the back of a utility vehicle and any other means of transporting the unit. It is available as a pull type unit which is designed for off road use and is not highway legal. For more information on the pull type unit look at our model number HS-150-P.
|Tank Capacity||150 Gallons|
|Engine||6.5 H.P. Honda recoil start|
|Pump||2″x 2″ centrifugal with 190 GPM and 42 P.S.I|
|Tires & Wheels||205/65-10 tires with 4 bolt hubs|
|Overall size||49″ x 88″ x 56″|
|Coverage (sq. ft)||2,000 sq. ft.|
|Empty Weight||370 pounds|
|Loaded Weight||1570 pounds|
|Standard Hose||100 feet|
|Mulch that can be used||100% paper and pourable mulches|
Turbo Turf HS-150-P
- Plus freight
- The shopping cart will not automatically add freight charges. We contact a large number of freight companies and use our large discounts to get the best shipping rates possible. We will not charge your card until we are ready to ship and will contact you with the exact charges for your approval before we charge your card.
Need to view your cart before checking out or want to check your order.
The HS-150-P can be equipped with a boom to use it as a lawn sprayer when you are not hydro seeding.
Booms are available in 6 feet spray pattern, 10 foot spray pattern and 16 foot spray pattern. See our option page for pricing.
The HS-150-P can also be equipped with what we call a “Seed & Spray” option which is a hose reel and hose for spraying herbicides, insecticides and fertilizers.